86 lines
2.4 KiB
C
86 lines
2.4 KiB
C
#include "hcsr04.h"
|
||
#include "tim.h"
|
||
|
||
// time 的单位是 μs
|
||
static uint64_t time; // 声明变量,用来计时
|
||
static uint64_t time_end; // 声明变量,存储回波信号时间
|
||
static uint8_t state = 1;
|
||
|
||
// HACK 临时的 delay 解决方法
|
||
void delay_us(uint16_t us);
|
||
|
||
int16_t sonar_mm(void) // 测距并返回单位为毫米的距离结果
|
||
{
|
||
uint32_t distance, distance_mm = 0;
|
||
HAL_GPIO_WritePin(SCL_C_GPIO_Port, SCL_C_Pin, GPIO_PIN_SET); // 输出高电平
|
||
delay_us(15); // 延时15微秒
|
||
HAL_GPIO_WritePin(SCL_C_GPIO_Port, SCL_C_Pin, GPIO_PIN_RESET); // 输出低电平
|
||
|
||
while (state)
|
||
;
|
||
state = 1;
|
||
|
||
// BUG 现在 time 的单位是 1μs
|
||
if (time_end / 100 < 38) // 判断是否小于38毫秒,大于38毫秒的就是超时,直接调到下面返回0
|
||
{
|
||
distance = (time_end * 346) / 2; // 计算距离,25°C空气中的音速为346m/s
|
||
distance_mm = distance / 100; // 因为上面的time_end的单位是10微秒,所以要得出单位为毫米的距离结果,还得除以100
|
||
}
|
||
return distance_mm; // 返回测距结果
|
||
}
|
||
|
||
float sonar(void) // 测距并返回单位为米的距离结果
|
||
{
|
||
uint32_t distance, distance_mm = 0;
|
||
float distance_m = 0;
|
||
HAL_GPIO_WritePin(SCL_C_GPIO_Port, SCL_C_Pin, GPIO_PIN_SET); // 输出高电平
|
||
delay_us(15); // 延时15微秒
|
||
HAL_GPIO_WritePin(SCL_C_GPIO_Port, SCL_C_Pin, GPIO_PIN_RESET); // 输出低电平
|
||
|
||
while (state)
|
||
;
|
||
state = 1;
|
||
|
||
// BUG 现在 time 的单位是 1μs
|
||
if (time_end / 100 < 38)
|
||
{
|
||
distance = (time_end * 346) / 2;
|
||
distance_mm = distance / 100;
|
||
distance_m = distance_mm / 1000;
|
||
}
|
||
return distance_m;
|
||
}
|
||
|
||
void delay_us(uint16_t us)
|
||
{
|
||
HAL_TIM_Base_Start_IT(&htim2);
|
||
time = 0;
|
||
while (time < us)
|
||
;
|
||
HAL_TIM_Base_Stop_IT(&htim2);
|
||
}
|
||
|
||
void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim)
|
||
{
|
||
if (htim == &htim2)
|
||
++time;
|
||
}
|
||
|
||
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
|
||
{
|
||
if (GPIO_Pin == SDA_C_EXTI12_Pin)
|
||
{
|
||
if (HAL_GPIO_ReadPin(SDA_C_EXTI12_GPIO_Port, SDA_C_EXTI12_Pin))
|
||
{
|
||
HAL_TIM_Base_Start_IT(&htim2);
|
||
time = 0;
|
||
}
|
||
else
|
||
{
|
||
time_end = time;
|
||
HAL_TIM_Base_Stop_IT(&htim2);
|
||
state = 0;
|
||
}
|
||
}
|
||
}
|